Contact HMS Store Manager

Goto HMS-Brightsign Home Page

Contact HMS Technical Support

International Shipping
Please Read!

Solution Graphics

HMS Home Logo

Solution Graphics

Buttons & Touch Sensors

! ! ! Print the Schematic and Specification Sheet for your Records. Product shipped without Documentation ! ! !

 

Proximity Touch Sensors & GPIO Adapters
Proximity Touch Sensor (Vertical Entry)

AZ-Sense2-V    $10.50
 2x2 inch Proximity 'Touch Sensor'.    Easily activated thru plastic, glass, wood, MDF or combination.  This sensor has 'Dynamic Calibration' that sets the proximity sensitivity on power-up.  Requires 'polarized' RJ11-6-4 phone cable and connections.

Note: Custom touch settings available.  Contact HMS Technical Support for custom gain settings.

Link: Specification Sheet

 AZ-Sense2 Vertical
Click Image for larger image
Proximity Touch Sensor (Horizontal Entry)

AZ-Sense2-H    $10.50
 2x2 inch Proximity 'Touch Sensor'.    Easily activated thru plastic, glass, wood, MDF or combination.  This sensor has 'Dynamic Calibration' that sets the proximity sensitivity on power-up.  Requires 'polarized' RJ11-6-4 phone cable and connections.

Note: Custom touch settings available.  Contact HMS Technical Support for custom gain settings.

Link: Specification Sheet

 AZ-Sense2 Horizontal
Click Image for larger image
Proximity Touch Sensor (Vertical Entry)

AZ-Sense2-V-TH    $20.50
 2x2 inch Proximity 'Touch & Hold Sensor'.    Contact 'Technical Support' for sensor programming.  Requires 'polarized' RJ11-6-4 phone cable and connections.

Note: Custom touch settings available.  Contact HMS Technical Support for custom gain settings.

Link: Specification Sheet

 AZ-Sense2 Vertical
Click Image for larger image
Proximity Touch Sensor (Horizontal Entry)

AZ-Sense2-H-TH    $20.50
 2x2 inch Proximity 'Touch & Hold Sensor'.   Contact 'Technical Support' for sensor programming.  Requires 'polarized' RJ11-6-4 phone cable and connections.

Note: Custom touch settings available.  Contact HMS Technical Support for custom gain settings.

Link: Specification Sheet

 AZ-Sense2 Horizontal
Click Image for larger image
Small, low profile

Proximity Touch Sensor (Small)
AZ-Sense1  $12.50

 1.0 x 0.9  inch Proximity 'Touch Sensor'.    Easily activated thru plastic, glass, wood, MDF or combination.  This sensor has 'Dynamic Calibration' that sets the proximity sensitivity on power-up.  3 wire connection (phone cable works)

Note: Custom touch settings available.  Contact HMS Technical Support for custom gain settings.  Or for pre-wiring of the phone cables to the sensor board.

Link: Specification Sheet
AZ-Sense1
Proximity Touch Sensor GPIO adapter (Series 3)
TB12-RJ11-4    $24.50
GPIO (Series 3 Machines) to RJ11-4-8 adapter specifically for the Proximity Touch Sensors above.  Can mount directly to the BrightSign GPIO. Attach to the GPIO using the pluggable terminal blocks that come with the 'Series 3' machines.

Link: Specification Sheet

 AZ-Sense 8 Adapter
Click Image for larger image
Proximity Touch Sensor GPIO adapter (Series 3)
TB12-RJ11-8    $28.50
GPIO to RJ11-4-8 adapter specifically for the Proximity Touch Sensor above.  Can mount directly to the BrightSign GPIO. Attach to the GPIO using the pluggable terminal blocks that come with the 'Series 3' machines.

Link: Specification Sheet

 AZ-Sense 8 Adapter
Click Image for larger image

 

HMS-I/O to Touch Sensor Adapter
AZ-Sense-Split   $22.50

 Phone Cable Adapter to simplify wiring.  Up to 8 AZ-Sense boards can be connected using the RJ11-6-4 telephone cables. Use a 10 conductor cable between this board and any HMS I/O board that has 3.3 volts on the 'input' terminal block.
Note:  For Sensors with LED's, the LED's lines are connected to 0Volts (always on). 		AZ-Sense 8 RJ11 to Cable Adapter
Link: RJ11 Cables 4 Conductor Phone Cables for the above modules  

Ambient Light Sensors
 
LDR-Sensor (New Item 11/2020)
Sensor Options
 1" x 1" Light Sensor.  Shipped with socket pins for the sensor (Light Dependent Resistor).  Cut the leads of the LDR to required length (scissors or wire cutters).  The output is high with ambient light and goes low when covered (dark).  The board size is 1.0 x 1.0 inches with 4 mounting holes in the corners.  This sensor is intended to be mounted under a shelf and the LDR cut to fit flush to the top of the shelf.  Not restricted to under shelf mounting. Options: -N (no cable, no socket), Options: -PW (Pre-Wired with 24" cable) Options: -S (3 pin socket)

Link: Specification Sheet

 AZ-Sense4Shown with 3 pin socket.  However, contact HMS Electronics (Technical Support) if you want the board pre-wired or socket installed.
 
 
 LDR-Sensor-L (New Item 11/2020)
Sensor Options
 1" x 1" Light Sensor.  Shipped with socket pins for the sensor (Light Dependent Resistor).  Cut the leads of the LDR to required length (scissors or wire cutters).  The output is low with ambient light and goes high when covered (dark).  The board size is 1.0 x 1.0 inches with 4 mounting holes in the corners.  This sensor is intended to be mounted under a shelf and the LDR cut to fit flush to the top of the shelf.  Not restricted to under shelf mounting. Options: -N (no cable, no socket), Options: -PW (Pre-Wired with 24" cable) Options: -S (3 pin socket)

Link: Specification Sheet

 AZ-Sense4
 
 

4-Way Proximity Touch Sensors & Adapters
 
 AZ4-Sense (4 Proximity Touch Sensors, Horizontal Entry)

Price Each:  $60.50 (USD)

 2x6.8 inch Proximity 'Touch Sensor'.  4 touch sensors spaced 1.5 inches.    Easily activated thru plastic, glass, wood, MDF or combination.  This sensor has 'Dynamic Calibration' that sets the proximity sensitivity on power-up.  Requires RJ45-8 phone cable and connections.

Link: Specification Sheet    Link: RJ45 Cables (8 Conductor)

 AZ-Sense4
Click Image for larger image
Link: RJ45 Cables 8 Conductor Cables for the 4-way proximity Sensors)  

Vandal Resistant Switches (Lighted, 12 Volts)

 VRS25-F12 (Momentary Switch, Lighted)

Price Each: $15.00 (USD)

LED Color
 25mm (1 inch) stainless body, flat actuator, 12 volt, ring lighting, momentary switch. Overall length below mounting = 40mm (plate bezel to terminals)

Panel Thickness 1 to 10mm

 Vandal Resistant Lighted Switch

 VRS19-F12 (Momentary Switch, Lighted)

Price Each: $12.00 (USD)

LED Color
 19mm (3/4 inch), stainless body, flat actuator, 12 volt, ring lighting, momentary switch

Panel Thickness 1 to 12mm

 Vandal Resistant Lighted Switch

Vandal Resistant Switches (Lighted, 3 Volts)

 VRS25-F-3V (Momentary Switch, Lighted, 3Volts)

Price Each: $15.50 (USD)

LED Color
 These are custom switches for direct connection to the BrightSign GPIO.  The BrightSign has  limit resistors built in, so these switches have no limit resistors.  These can only be used for the BrightSign GPIO (unless you add external limit resistor)  Use the DB15-TB10-3V adapter for connections to the Older BrightSign GPIO.

25mm (1 inch) , stainless body, flat actuator, 3.3 volt, ring lighting, momentary switch

Panel Thickness 1 to 10mm

 Vandal Resistant Lighted Switch

 VRS19-F-3V (Momentary Switch, Lighted, 3Volts)

Price Each: $12.50 (USD)

LED Color
 These are custom switches for direct connection to the BrightSign GPIO.  The BrightSign has  limit resistors built in, so these switches have no limit resistors.  These can only be used for the BrightSign GPIO (unless you add external limit resistor)  Use the DB15-TB10-3V adapter for connections to the BrightSign GPIO.

19mm (3/4 inch) , stainless body, flat actuator, 3.3 volt, ring lighting, momentary switch

Panel Thickness 1 to 12mm

 Vandal Resistant Lighted Switch

Vandal Resistant Switches (Non Lighted)

 VRS19-F (Momentary Switch, Flat)

Price Each:  $6.50 (USD)

 19mm (3/4 inch), stainless body, flat actuator (NON-LIGHTED), momentary switch

Panel Thickness 1 to 10mm

 Vandal Resistant Switch (Flat)

 VRS19-D (Momentary Switch, Domed)

Price Each: $6.50 (USD)

 19mm (3/4 inch), stainless body, domed actuator (NON-LIGHTED), momentary switch

Panel Thickness 1 to 10mm

 Vandal Resistant Switch (Domed)
    Vandal Resistant Switch Terminals Terminal View of the above switches
VRS25-D (Momentary Switch Domed)

Price Each: $9.50 (USD)

 25mm (1 inch), stainless body, domed actuator (NON-LIGHTED), momentary switch

Panel Thickness 1 to 10mm

 		 Vandal Resistant Switch Terminals

Shown with pin connections (N/O Switch)
Pre-wiring available (call for quote)  (specify length for each switch)    

ARCADE STYLE LIGHTED BUTTONS (SWITCHES)

 HC-SR (Momentary Switch, Flat, 12V)

Lens Colors: Blue,Green,Red,White

Price Each:  $6.50 (USD)

Lens Color
 25mm (1,0 inch), stainless body, flat actuator, LIGHTED), momentary switch.  High Reliability micro switch. 1.0" hole size.  Twist & Lock Assembly.

Panel Thickness 1 to 20mm

 Vandal Resistant Switch (Flat)

White Lens shown

 HC-SR-LAMP (12V replacement lamp)

Led Colors: Red,White

Non-Stocked: Blue,Green

Price Each:  $2.00 (USD)

 25mm (1,0 inch), stainless body, flat actuator, LIGHTED), momentary switch.  High Reliability micro switch. 1.0" hole size.  Twist & Lock Assembly.  Includes white, 12V, wedge base lamp.

Panel Thickness 1 to 20mm

  

 
 
Diskettegpio_text.brs Free script file (BrightScript) to output messages to the screen showing the results of gpio events.  Rename this file to 'autorun.brs' and put it on the sdcard.  
 

 

Author: Richard Harkey
Copyright © 2009 HMS Electronics. All rights reserved.
Revised: April 12, 2022